The Computer bus reference article from the English Wikipedia on 24-Apr-2004
(provided by Fixed Reference: snapshots of Wikipedia from wikipedia.org)

Computer bus

Connect with a children's charity on your social network


In computer architecture, a bus is a subsystem that transfers data or power between computer components inside a computer or between computers.  Unlike a point-to-point connection, a bus can logically connect several peripherals over the same set of wires.

Early computer buses were literally parallel electrical buses with multiple connections, but the term is now used for any physical arrangement that provides the same logical functionality as a parallel electrical bus. Modern computer buses can use both parallel and bit-serial connections, and can be wired in either a multidrop (electrical parallel) or daisy chain topology, or connected by switched hubs, as in the case of USB.

Table of contents
1 History
2 Description
3 Examples of Internal Computer Buses
4 Examples of External Computer Buses
5 Examples of Internal/External Computer Buses
6 See also
7 External link

History

Early computer buses were bundles of wire that attached memory and peripherals. They were named after electrical buses, or busbars. Almost always, there was one bus for memory, and another for peripherals, and these were accessed by separate instructions, with completely different timings and protocols.

One of the first complications was the use of interrupts. Early computers performed I/O by waiting in a loop for the peripheral to become ready. This was a waste of time for programs that had other tasks to do. Also, if the program attempted to perform those other tasks, it might take too long for the program to check again, resulting in lost data. Engineers thus arranged for the peripherals to interrupt the CPU. The interrupts had to be prioritised, because the CPU can only execute code for one peripheral at a time, and some devices are more time-critical than others.

Some time after this, some computers (such as the RCA Spectra, running Multics) began to share memory between several CPUs. On these computers, access to the bus had to be prioritised, as well.

The classic, simple way to prioritise interrupts or bus access was with a daisy chain.

DEC noted that having two buses seemed wasteful and expensive for small, mass-produced computers, and mapped peripherals into the memory bus, so that the devices appeared to be memory locations. At the time, this was a very daring design. Cynics predicted failure.

Early microcomputer bus systems were essentially a passive backplane connected to the pins of the CPU. Memory and other devices would be added to the bus using the same address and data pins as the CPU itself used, connected in parallel. In some instances, such as the IBM PC, instructions still generated signals at the CPU that could be used to implement a true I/O bus.

In many microcontrollers and embedded systems, an I/O bus still does not exist. Communication is controlled by the CPU, which reads and writes data from the devices as if they are blocks of memory (in most cases), all timed by a central clock controlling the speed of the CPU. Devices ask for service by signalling on other CPU pins, typically using some form of interrupt.

For instance, a disk drive controller would signal the CPU that new data was ready to be read, at which point the CPU would move the data by reading the memory that corresponded to the disk drive. Almost all early computers were built in this fashion, starting with the S-100 bus in the Altair, and continuing through the IBM PC in the 1980s.

These simple bus systems had a serious drawback for general-purpose computers. All the equipment on the bus has to talk at the same speed, and thus shares a single clock.

Increasing the speed of the CPU is not a simple matter, because the speed of all the devices must increase as well. This often leads to odd situations where very fast CPUs have to "slow down" in order to talk to other devices in the computer. While acceptable in embedded systems, this problem was not tolerated for long in commercial computers.

Another problem is that the CPU is required for all operations, so if it becomes busy with other tasks, the real throughput of the bus could suffer dramatically.

Such bus systems are difficult to configure when constructed from common off-the-shelf equipment. Typically each added PC board requires many jumpers in order to set memory addresses, I/O addresses, interrupt priorities, and interrupt numbers.

"Second generation" bus systems like NuBus addressed some of these problems. They typically separated the computer into two "worlds", the CPU and memory on one side, and the various devices on the other, with a \bus controller in between. This allowed the CPU to increase in speed without affecting the bus. This also moved much of the burden for moving the data out of the CPU and into the cards and controller, so devices on the bus could talk to each other with no CPU intervention. This led to much better "real world" performance, but also required the cards to be much more complex. These buses also often addressed speed issues by being "bigger" in terms of the size of the data path, moving from 8-bit parallel buses in the first generation, to 16 or 32-bit in the second, as well as adding software setup (now standardised as Plug-n-play) to supplant or replace the jumpers.

However these newer systems shared one quality with their earlier cousins, in that everyone on the bus had to talk at the same speed. While the CPU was now insulated and could increase speed without fear, CPUs and memory continued to increase in speed much faster than they buses they talked to. The result was that the bus speeds were now very much slower than what a modern system needed, and the machines were left starved for data. A particularly common example of this problem was that video cards quickly outran even the newer bus systems like PCI, and now computers include the AGP bus just to drive the video card.

During this period an increasing number of external devices started employing their own bus systems as well. When disk drives were first introduced, they would be added to the machine with a card plugged into the bus, which is why computers have so many slots on the bus. But through the 1980s and 1990s, new systems like SCSI and IDE were introduced to serve this need, leaving most slots in modern systems empty. Today there are likely to be about five different buses in the typical machine, supporting various devices.

A useful differentiation then became popular, the concept of the local bus as opposed to external bus. The former referred to bus systems that were designed to be used with internal devices, such as graphics cards, and the latter to buses designed to add external devices such as scanners. This definition was always soft: IDE is an external bus in terms of how it is used, but is almost always found inside the machine.

"Third generation" buses are now in the process of coming to market, including HyperTransport and InfiniBand. They typically include features that allow them to run at the very high speeds needed to support memory and video cards, while also supporting lower speeds when talking to slower devices such as disk drives. They also tend to be very flexible in terms of their physical connections, allowing them to be used both as internal buses, as well as connecting different machines together. This can lead to complex problems when trying to service different requests, so much of the work on these systems concerns software design, as opposed to the hardware itself. In general, these third generation buses tend to look more like a network than the original concept of a bus, with a higher protocol overhead needed than early systems, while also allowing multiple devices to use the bus at once.

Description

At one time, "bus" meant an electrically parallel system, with electrical conductors similar or identical to the pins on the CPU. This is no longer the case, and modern systems are blurring the lines between buses and networks.

Buses can be parallel buses, which carry data words striped across multiple wires, or serial buses, which carry data in bit-serial form. The addition of extra power and control connections, differential drivers, and data connections in each direction usually means that most serial buses have more conductors than the minimum of two used in the I²C serial bus. As data rates increase, the problems of timing skew across parallel buses become more and more difficult to circumvent, to the point where a serial bus can actually be operated at higher overall data rates than a parallel bus, despite having fewer electrical connections. USB, firewire, and Serial ATA are examples of this. Multidrop connections do not work well for fast serial buses, so most modern serial buses use daisy-chain or hub designs.

Most computers have both internal and external buses. An internal bus connects all the internal components of a computer to the motherboard (and thus, the CPU and internal memory). These types of buses are also referred to as a local bus, because they are intended to connect to local devices, not to those in other machines or external to the computer. An external bus connects external peripherals to the motherboard.

Network connections such as Ethernet are not generally regarded as buses, although the difference is largely conceptual rather than practical. The arrival of technologies such as InfiniBand and HyperTransport is further blurring the boundaries between networks and buses. Even the lines between internal and external are sometimes fuzzy, I²C can be used as both an internal bus, or an external bus (where it is known as ACCESS.bus), and InfiniBand is intended to replace both internal buses like PCI as well as external ones like Fibre Channel.

Modern trends in personal computers, especially laptops, have been moving towards eliminating all external connections except for modem jack, CAT5, USB, sounds, and optional VGA.

Examples of Internal Computer Buses

Parallel

Serial

Examples of External Computer Buses

Parallel

Serial

Proprietary

keyboard bus mouse connector PS/2 mouse connector floppy drive connector


Examples of Internal/External Computer Buses

See also

External link